All Categories

Home>Products>Alloy Steel Pipes>Low-Temperature Seamless alloy Pipe

Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel

HTB1Tcjpf8cHL1JjSZJiq6AKcpXaQ
astm-a333-gr8-ultra-low-temperature-steel-pipe
astm-a333-grade-6_seamless-pipe
HTB1hU7KaET1gK0jSZFrq6ANCXXa6
HTB1lOoKaEY1gK0jSZFMq6yWcVXaV
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel

Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel

Low Temperature Alloy Seamless Pipes

Alloy Seamless Pipes Nickel Steel

Pressure Purpose Alloy ferritic Pipes

Alloy Seamless Pipes Lighting Poles

Annealing mild alloy steel tube

EN10216-4; 

26CrMo4-2, 12Ni14;


Inquiry
  • Description
  • Specification
  • Comments

Description:
Low-Temperature Service Alloy Steel Pipe is based on standard ASTM A333. Pipe grades permit low temperature service. This specification covers nominal (average) walled pipe almost exclusively in seamless. Several grades of ferritic steel are included. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse effect on low-temperature impact properties.

Applications:
Brief Introduction:
Low-Temperature Service Alloy Steel Pipe is based on standard ASTM A333. Pipe grades permit low temperature service. This specification covers nominal (average) walled pipe almost exclusively in seamless. Several grades of ferritic steel are included. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse effect on low-temperature impact properties.

Specifications
Outside Diameter:21.3mm - 711.2mm
Wall Thickness:  2mm- 150mm
Length:  1m-12m

37

Standard

ASTM A333

Low-Temperature Service Alloy Steel Pipe

N08800

 a kind of corrosion resistant alloy steel   pipe, the Cr content is 15-25%, the nickel content is 30-45%

ASTM A556 / A556M

Seamless Cold-Drawn Carbon Steel Feedwater Heater   Tubes

GB 18248 / JIS G3429

For the manufacture of pressure vessels, gas   cylinders seamless.

 ASTM A335 ASME S/A335

 for High-Temperature Service

ASTM A369

 Forged and Bored Pipe for High-Temperature   Service

ASTM A519

For mechanical engineering,  mechanical and   pressure use,and also for transporting steam,water,gas and etc.

ASTM A209

Alloy-Steel boiler and superheater tubes a kind of   C-Mo-Alloy seamless steel pipe/tube for boiler and Superheater service

ASTM A250

Alloy steel boiler tubes

ASTM A213

Heat Transfer Boiler Tubes

38

Grade:

Standard

Grade

OD

WT

ASTM A333

16MnDG, 10MnDGM, 09DG, 09Mn2VDG, 06Ni3MoDG, ASTM   A333-Grade1, Grade3, Grade4, Grade6, Grade7, Grade8, Grade9, Grade10, Grade11

1/2" to 24"

4mm to 70mm

N08800

N08800

1/2" to 24"

4mm to 70mm

ASTM A556 / A556M

SA556Gr.B2, SA556Gr.C2

 12mm – 40mm

 1mm – 5mm

GB 18248 / JIS G3429

37Mn, 34Mn2V, 30CrMo, 35CrMo, STH11, STH12, STH21,   STH22

 12mm – 114.3mm

 2mm – 22mm

 ASTM A335 ASME S/A335

P-5, P-9, P-11, P-22, P-91

19.05mm -610mm

3.0mm -150mm

ASTM A369

FP1, FP2,  FP5, FP9,FP11, FP12,FP21,FP22,FP91,   FP92

12.5mm-824mm

 2mm-100mm

ASTM A519

1020, 1025, 1035, 1045, 4130, 4140

10-324mm

1-30mm

ASTM A209

T1, T1a, T1b

OD: 3/4" (19.05), 1"(25.4) ,   1-1/4"(31.75), 1-1/2"(38.1), 2" (50.8), 2-1/2"(63.5) ,   3" (76.2)

1-15mm

ASTM A250

T1, T1a, T1b, T2, T11, T12, and T22

1/2"-5"(12.7-127mm)

0.035"-0.320" (0.9-8.1mm)

ASTM A213

T1, T5, T9, T11, T22, T91

1/2"-5"(12.7-127mm)

0.015 to 0.500 in. [0.4 to 12.7 mm],

Note:Other size can also be provided after consuliting with customers

Description
Low-Temperature Service Alloy Steel Pipe used in cryogenic alloy tubes is comparable to that of carbon structural steels. The utility model has the advantages of high strength, good comprehensive performance, long service life, wide application range, relatively economic, etc.. It is widely used in bridges, ships, boilers, vehicles and important building.


Normal Grade Chemical Requirements



Composition, %


Element

Grade 1

Grade 3

Grade 6

Carbon, max

0.3

0.19

0.3

Manganese

0.40  1.06

0.31  0.64

0.29  1.06

Phosphorous, max

0.025

0.025

0.025

Sulfur, max

0.025

0.025

0.025

Silicon

0.18 -0.37

0.10 min

Nickel

3.18  3.82


Normal Steel grade:
ASTM A333 Grade 6

Packing:
Bare packing / bundle packing / crate packing / wooden protection at the both sides of tubes and suitably protected for sea-worthy delivery or as requested.

Inspection and Test:
Chemical Composition Inspection
Mechanical Properties Test (Tensile Strength, Yield Strength, Elongation, Flaring, Flattening, Bending, Hardness, Impact Test)
Surface and Dimension Test
No-destructive Test
Hydrostatic Test

Surface treatment:
Oil-dip, Varnish, Passivation, Phosphating, Shot Blasting.
Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested.

Chemical requirement Composition (%)
Composition ASTM A333 Grade 6
Carbon, max 0.30
Manganese 0.29–1.06
Phosphorus, max 0.025
Sulfur, max 0.025
For each reduction of 0.01% carbon below 0.30%, an increase of 0.05% manganese above 1.06% would be permitted to a maximum of 1.35% manganese.

Tensile requirements
Data ASTM A333 Grade 6
Tensile strength, min, psi (MPa) 60 000 (415)
Yield strength, min, psi (MPa) 35 000 (240)

Impact temperature
Minimum Impact Test Temperature -45 °C(-50 F)

Notes for Bend Test
For pipe whose diameter exceeds NPS 25 and whose diameter to wall thickness ratio is 7.0 or less shall be subjected to the bend test instead of the flattening test.
Other pipe whose diameter equals or exceeds NPS 10 may be given the bend test in place of the flattening test subject to the approval of the purchaser.
The bend test specimens shall be bent at room temperature through 180 without cracking on the outside of the bent portion.


Trusted Customers or End Users of Low-Temperature Seamless alloy Pipe:5

Standard

Grade

OD

WT

ASTM A333

16MnDG, 10MnDGM, 09DG, 09Mn2VDG, 06Ni3MoDG, ASTM   A333-Grade1, Grade3, Grade4, Grade6, Grade7, Grade8, Grade9, Grade10, Grade11

1/2" to 24"

4mm to 70mm

N08800

N08800

1/2" to 24"

4mm to 70mm

ASTM A556 / A556M

SA556Gr.B2, SA556Gr.C2

 12mm – 40mm

 1mm – 5mm

GB 18248 / JIS G3429

37Mn, 34Mn2V, 30CrMo, 35CrMo, STH11, STH12, STH21,   STH22

 12mm – 114.3mm

 2mm – 22mm

 ASTM A335 ASME S/A335

P-5, P-9, P-11, P-22, P-91

19.05mm -610mm

3.0mm -150mm

ASTM A369

FP1, FP2,  FP5, FP9,FP11, FP12,FP21,FP22,FP91,   FP92

12.5mm-824mm

 2mm-100mm

ASTM A519

1020, 1025, 1035, 1045, 4130, 4140

10-324mm

1-30mm

ASTM A209

T1, T1a, T1b

OD: 3/4" (19.05), 1"(25.4) ,   1-1/4"(31.75), 1-1/2"(38.1), 2" (50.8), 2-1/2"(63.5) ,   3" (76.2)

1-15mm

ASTM A250

T1, T1a, T1b, T2, T11, T12, and T22

1/2"-5"(12.7-127mm)

0.035"-0.320" (0.9-8.1mm)

ASTM A213

T1, T5, T9, T11, T22, T91

1/2"-5"(12.7-127mm)

0.015 to 0.500 in. [0.4 to 12.7 mm],


Delivery is very timely.       ___Pulitzer (Peru)


Pipe is good-looking on appearance.        ___Armstrong (Mexico)


Logistics is fast and no delay the project schedule.      ___Bartholomew (Belgium)


Delivery is fast even shortens a few days.       ___Augustine (Kenya)


Sales is very professional, good.      ___Catherine (Thailand)

INQUIRY