ប្រភេទទាំងអស់

ទំព័រដើម>ផលិតផល>បំពង់ដែកអ៊ីណុក>បំពង់ដែកគ្មានថ្នេរសីតុណ្ហភាពទាប

ផលិតផល

Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel

HTB1Tcjpf8cHL1JjSZJiq6AKcpXaQ
astm-a333-gr8-ultra-low-temperature-steel-pipe
astm-a333-grade-6_seamless-pipe
HTB1hU7KaET1gK0jSZFrq6ANCXXa6
HTB1lOoKaEY1gK0jSZFMq6yWcVXaV
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel
Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel

Low-Temperature Seamless Alloy Pipe, Alloy Seamless Pipes Nickel Steel

Low Temperature Alloy Seamless Pipes

Alloy Seamless Pipes Nickel Steel

Pressure Purpose Alloy ferritic Pipes

Alloy Seamless Pipes Lighting Poles

Annealing mild alloy steel tube

EN10216-4; 

26CrMo4-2, 12Ni14;


ស៊ើបអង្កេត
  • ការពិពណ៌នា
  • ការបញ្ជាក់លម្អិត
  • យោបល់

អធិប្បាយ:
Low-Temperature Service Alloy Steel Pipe is based on standard ASTM A333. Pipe grades permit low temperature service. This specification covers nominal (average) walled pipe almost exclusively in seamless. Several grades of ferritic steel are included. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse effect on low-temperature impact properties.

កម្មវិធី:
ការណែនាំខ្លីៗ:
Low-Temperature Service Alloy Steel Pipe is based on standard ASTM A333. Pipe grades permit low temperature service. This specification covers nominal (average) walled pipe almost exclusively in seamless. Several grades of ferritic steel are included. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse effect on low-temperature impact properties.

លក្ខណៈពិសេស
អង្កត់ផ្ចិតខាងក្រៅ: 21.3mm - 711.2mm
កម្រាស់ជញ្ជាំង: 2mm-150mm
ប្រវែង: 1m-12m

37

Standard:

ASTM A333

សេវាសីតុណ្ហភាពទាប បំពង់ដែកអ៊ីណុក

N08800

 a kind of corrosion resistant alloy steel   pipe, the Cr content is 15-25%, the nickel content is 30-45%

ASTM A556 / A556M

បំពង់កំដៅទឹកកាបូនដែកកាបូនដែលគូរដោយត្រជាក់គ្មានថ្នេរ

GB 18248 / JIS G3429

សម្រាប់ការផលិតធុងសម្ពាធ ស៊ីឡាំងឧស្ម័នគ្មានថ្នេរ។

 ASTM A335 ASME S/A335

 សម្រាប់សេវាកម្មសីតុណ្ហភាពខ្ពស់។

ASTM A369

 បំពង់បំរែបំរួលនិងអផ្សុកសម្រាប់សេវាកម្មសីតុណ្ហភាពខ្ពស់។

ASTM A519

សម្រាប់វិស្វកម្មមេកានិក ការប្រើប្រាស់មេកានិក និងសម្ពាធ ព្រមទាំងសម្រាប់ការដឹកជញ្ជូនចំហាយទឹក ឧស្ម័ន និងល។

ASTM A209

ឡចំហាយ និងបំពង់ដែកអ៊ីណុក Alloy-Steel boiler and superheater tubes ជាប្រភេទ C-Mo-Alloy steel pipe/tube for boiler and Superheater services

ASTM A250

បំពង់ឡចំហាយដែកអ៊ីណុក

ASTM A213

បំពង់ផ្ទេរកំដៅ boiler

38

ថ្នាក់:

Standard

ថ្នាក់ទី

OD

WT

ASTM A333

16MnDG, 10MnDGM, 09DG, 09Mn2VDG, 06Ni3MoDG, ASTM A333-Grade1, Grade3, Grade4, Grade6, Grade7, Grade8, Grade9, Grade10, Grade11

១/២ "ទៅ ៨"

4mm ដើម្បី 70mm

N08800

N08800

១/២ "ទៅ ៨"

4mm ដើម្បី 70mm

ASTM A556 / A556M

SA556Gr.B2, SA556Gr.C2

 12mm - 40mm

 1mm - 5mm

GB 18248 / JIS G3429

37Mn, 34Mn2V, 30CrMo, 35CrMo, STH11, STH12, STH21, STH22

 12mm - 114.3mm

 2mm - 22mm

 ASTM A335 ASME S/A335

P-5, P-9, P-11, P-22, P-91

19.05 មម -610 ម

3.0 មម -150 ម

ASTM A369

FP1, FP2, FP5, FP9, FP11, FP12, FP21, FP22, FP91, FP92

12.5mm-824mm

 2mm-100mm

ASTM A519

1020, 1025, 1035, 1045, 4130, 4140

10-324mm

1-30mm

ASTM A209

T1, T1a, T1b

OD៖ 3/4" (19.05), 1"(25.4), 1-1/4"(31.75), 1-1/2"(38.1), 2" (50.8), 2-1/2"(63.5) ) , 3" (76.2)

1-15mm

ASTM A250

T1, T1a, T1b, T2, T11, T12, និង T22

1/2"-5"(12.7-127mm)

១ "-៦" (២៥-១៥០ មម)

ASTM A213

T1, T5, T9, T11, T22, T91

1/2"-5"(12.7-127mm)

0.015 ទៅ 0.500 in. [0.4 ទៅ 12.7 mm],

ចំណាំ៖ ទំហំផ្សេងទៀតក៏អាចផ្តល់ជូនផងដែរ បន្ទាប់ពីបានប្រឹក្សាជាមួយអតិថិជន

ការពិពណ៌នា
Low-Temperature Service Alloy Steel Pipe used in cryogenic alloy tubes is comparable to that of carbon structural steels. The utility model has the advantages of high strength, good comprehensive performance, long service life, wide application range, relatively economic, etc.. It is widely used in bridges, ships, boilers, vehicles and important building.


Normal Grade Chemical Requirements



Composition, %


ធាតុ

ថ្នាក់ 1

ថ្នាក់ 3

ថ្នាក់ 6

Carbon, max

0.3

0.19

0.3

ម៉ានហ្គាណា

0.40 - 1.06

0.31 - 0.64

0.29 - 1.06

Phosphorous, max

0.025

0.025

0.025

Sulfur, max

0.025

0.025

0.025

តំបន់ Silicon

0.18 -0.37

0.10 នាទី

nickel

3.18 - 3.82


Normal Steel grade:
ASTM A333 Grade 6

វេចខ្ចប់:
Bare packing / bundle packing / crate packing / wooden protection at the both sides of tubes and suitably protected for sea-worthy delivery or as requested.

Inspection and Test:
Chemical Composition Inspection
Mechanical Properties Test (Tensile Strength, Yield Strength, Elongation, Flaring, Flattening, Bending, Hardness, Impact Test)
Surface and Dimension Test
No-destructive Test
តេស្តអ៊ីដ្រូស្តាទិច

ការព្យាបាលលើផ្ទៃ:
Oil-dip, Varnish, Passivation, Phosphating, Shot Blasting.
Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested.

Chemical requirement Composition (%)
Composition ASTM A333 Grade 6
Carbon, max 0.30
Manganese 0.29–1.06
Phosphorus, max 0.025
Sulfur, max 0.025
For each reduction of 0.01% carbon below 0.30%, an increase of 0.05% manganese above 1.06% would be permitted to a maximum of 1.35% manganese.

Tensile requirements
Data ASTM A333 Grade 6
Tensile strength, min, psi (MPa) 60 000 (415)
Yield strength, min, psi (MPa) 35 000 (240)

Impact temperature
Minimum Impact Test Temperature -45 °C(-50 F)

Notes for Bend Test
For pipe whose diameter exceeds NPS 25 and whose diameter to wall thickness ratio is 7.0 or less shall be subjected to the bend test instead of the flattening test.
Other pipe whose diameter equals or exceeds NPS 10 may be given the bend test in place of the flattening test subject to the approval of the purchaser.
The bend test specimens shall be bent at room temperature through 180 without cracking on the outside of the bent portion.


Trusted Customers or End Users of Low-Temperature Seamless alloy Pipe:5

Standard

ថ្នាក់ទី

OD

WT

ASTM A333

16MnDG, 10MnDGM, 09DG, 09Mn2VDG, 06Ni3MoDG, ASTM A333-Grade1, Grade3, Grade4, Grade6, Grade7, Grade8, Grade9, Grade10, Grade11

១/២ "ទៅ ៨"

4mm ដើម្បី 70mm

N08800

N08800

១/២ "ទៅ ៨"

4mm ដើម្បី 70mm

ASTM A556 / A556M

SA556Gr.B2, SA556Gr.C2

 12mm - 40mm

 1mm - 5mm

GB 18248 / JIS G3429

37Mn, 34Mn2V, 30CrMo, 35CrMo, STH11, STH12, STH21, STH22

 12mm - 114.3mm

 2mm - 22mm

 ASTM A335 ASME S/A335

P-5, P-9, P-11, P-22, P-91

19.05 មម -610 ម

3.0 មម -150 ម

ASTM A369

FP1, FP2, FP5, FP9, FP11, FP12, FP21, FP22, FP91, FP92

12.5mm-824mm

 2mm-100mm

ASTM A519

1020, 1025, 1035, 1045, 4130, 4140

10-324mm

1-30mm

ASTM A209

T1, T1a, T1b

OD៖ 3/4" (19.05), 1"(25.4), 1-1/4"(31.75), 1-1/2"(38.1), 2" (50.8), 2-1/2"(63.5) ) , 3" (76.2)

1-15mm

ASTM A250

T1, T1a, T1b, T2, T11, T12, និង T22

1/2"-5"(12.7-127mm)

១ "-៦" (២៥-១៥០ មម)

ASTM A213

T1, T5, T9, T11, T22, T91

1/2"-5"(12.7-127mm)

0.015 ទៅ 0.500 in. [0.4 ទៅ 12.7 mm],


Delivery is very timely.       ___Pulitzer (Peru)


Pipe is good-looking on appearance.        ___Armstrong (Mexico)


ភស្តុភារមានល្បឿនលឿន និងមិនមានការពន្យាពេលគម្រោង។ ___Bartholomew (បែលហ្សិក)


Delivery is fast even shortens a few days.       ___Augustine (Kenya)


Sales is very professional, good.      ___Catherine (Thailand)

សាកសួរ